Fingerprint vs face vs card vs mobile attendance: which should you choose?
A neutral comparison of the four common ways to record attendance, the practical factors that decide between them, how punches reach payroll, and the questions to ask a supplier before you buy.
Choosing an attendance device usually starts in a shop or a supplier's catalogue, with a question about price. The better starting question is what you need to prevent and where the punches must end up. A device that stops colleagues clocking in for each other but cannot send its records to payroll without someone copying a USB stick every month solves half the problem. This guide compares fingerprint, face recognition, card (RFID) and mobile GPS attendance on the points that matter in practice, then covers connectivity and a checklist for suppliers. For the software side, see the attendance system for Jordanian companies; for the step-by-step device setup, read how to connect a ZKTeco device to payroll.
The four options at a glance
| Factor | Fingerprint | Face | Card (RFID) | Mobile GPS |
|---|---|---|---|---|
| Stops buddy punching | Strong | Strong | Weak: cards can be lent | Medium: depends on phone and location controls |
| Contact | Touch | Touch-free | Touch-free or a tap | Own phone |
| Speed at shift change | Good | Very good | Very good | Each person on own phone |
| Hard conditions | Worn or dirty fingers, gloves | Strong sunlight, helmets, masks | Lost or forgotten cards | Weak signal, indoor GPS drift |
| Recurring cost | Low | Low | Replacement cards | Software only |
| Biometric data | Yes | Yes | No | No (unless photo check-in) |
Fingerprint
Fingerprint terminals are still the most common choice in Jordanian offices and factories, and for good reason: they are familiar, mature and make it hard for one person to punch for another. Their weak spot is the finger itself. Staff who work with cement, chemicals or rough materials often have worn or damaged prints, and the device rejects them several times before accepting, or never does. Dust and moisture on the sensor have the same effect. Enrol two or three fingers per employee and keep a fallback, such as a card or PIN for the few people the sensor cannot read, with a supervisor reviewing those punches. Touch is the other issue: a shared sensor that hundreds of people press each day needs regular cleaning, a point many companies took more seriously after 2020.
Face recognition
Face terminals are touch-free and fast at shift change, since staff only walk up and look at the screen. Modern models use infrared or visible light, and many cope with glasses and changes in appearance. Lighting is the main risk: a device facing a glass door in direct sun, or mounted outside without a hood, struggles. Safety helmets and face masks can also slow recognition, depending on the model. Ask the supplier to demonstrate the device in conditions like yours, not in a showroom.
Card (RFID)
Cards are the fastest and cheapest per punch, and they work with dirty hands and gloves. They also have the obvious flaw: a card proves the card was there, not the person. One employee can tap for a colleague, and many companies discover this only when they compare attendance with CCTV. Cards also get lost, forgotten or broken, which adds a small but steady cost. Cards fit best where the same card already opens doors, or combined with a fingerprint or face as a second factor. Card technologies differ by frequency and format, so check that the cards you already use for access control are compatible.
Mobile GPS check-in
For sales reps, technicians, drivers and staff on client sites, a fixed device is not an option. Mobile attendance lets employees check in from their phone, with a geofence around the work location so a check-in from home is refused. Its strengths are no hardware and no queue; its weaknesses are phones without data, GPS drift inside buildings, and the risk of location spoofing apps. Some systems add a selfie at check-in to reduce sharing of phones, others do not. Mobile check-in works best as a complement to devices at fixed sites, with a clear rule on who may use it.
Privacy: biometric data is sensitive
Fingerprints and face templates are biometric data, which Jordan's Personal Data Protection Law No. 24 of 2023 lists as sensitive personal data. Before rolling out biometric attendance, tell employees what is collected and why, limit who can access the device and the templates, and plan what happens to an employee's data when they leave. For specific obligations, check with a legal adviser, since the implementing rules were still developing when this guide was written.
Connectivity: how punches reach payroll
The device type matters less than how its records leave the device. There are three common ways:
- Push to a server (ADMS / cloud). The device itself connects out over the internet and sends each punch to the attendance server as it happens. ZKTeco describes its standalone push communication devices as connecting over Ethernet, Wi-Fi or mobile data. Because the connection starts from the device, branches usually need no fixed IP or open ports, which makes this the simplest option for several sites.
- Pull over the local network. Software on a computer in the same network connects to the device and downloads the records. It works well on one site but needs a computer running on site, and remote branches need a VPN or a bridge.
- USB or file export. Someone downloads the records to a flash drive and imports them. It works anywhere but is slow, easy to forget and impossible to monitor live.
Ask which of these the device supports, and which the attendance software supports, before buying. Two devices that look identical can differ in firmware and in whether push is available.
Cost factors (without prices)
We do not quote device prices, because they depend on model, supplier and quantity. The factors that drive total cost are the same everywhere:
- Capacity: the number of users, faces, fingerprints and stored records the device holds.
- Housing: indoor or weather-resistant for outdoor gates.
- Attendance only, or access control with door locks and wiring.
- Cards, if used, and replacements.
- Network: cabling, Wi-Fi coverage or a mobile data SIM at each site.
- Power: a battery backup so punches are not lost in an outage.
- Installation, enrolment time, warranty and maintenance.
- Software licences and how the device connects to it.
Questions to ask before you buy
- Does this exact model and firmware support push (ADMS / cloud server) communication?
- How many users and records does it hold, and what happens when memory is full?
- Can it be demonstrated in our lighting, dust and glove conditions?
- What fallback exists for staff the sensor cannot read?
- Will it work with our payroll or HR software, and who sets that up?
- What warranty, spare parts and local support are available?
- How are biometric templates protected and deleted?
Once punches flow, the next step is rules: shifts, grace minutes and overtime. Our guide to shift scheduling covers rosters.
How Aspirations handles attendance
Aspirations attendance is designed for ZKTeco devices through ADMS push and a LAN bridge, plus file import; we confirm your model during setup. Staff in the field can check in and out with geofenced GPS from their phone browser, with one work location per employee; there is no selfie or photo check-in, and the native mobile app is built and coming to the stores. Shift templates with breaks, grace and overnight shifts feed a roster grid, and applying rosters writes lateness, early leave and overtime into attendance. Absence is not deducted from payroll automatically: HR reviews it, and employees request corrections with a reason through employee self-service. Plans are being finalised; a free trial is available.
This guide is general information. Check device capabilities with the manufacturer or supplier, and data protection obligations with a legal adviser.
